數碼視訊Q7刷機問題

zeusa · 發表于 2023-3-18 00:03

S905L3的處理器線刷成功，以下是ttl跑碼信息：BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 7, adc=528
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB

DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz
bist_test rank: 0 1b 03 34 31 1a 48 18 00 30 3b 23 54 17 00 2f 37 25 4a 16 00 2c 39 23 50 637 - PASS

Rank0: 1024MB(auto)-2T-13
0.0;
TE: 2264653

BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 7, adc=524
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB
0.0;
TE: 2462040

BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 7, adc=525
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB
Load fip header from USB, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from USB, src: 0x00010000, des: 0x013c0000, size: 0x00007600
Load bl301 from USB, src: 0x00018000, des: 0x01380000, size: 0x00002200
Load bl31 from USB, src: 0x0001c000, des: 0x10100000, size: 0x00019600
Load bl33 from USB, src: 0x00038000, des: 0x01000000, size: 0x00047200
NOTICE:  BL3-1: v1.0(debug):361f8a7
NOTICE:  BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07]
efuse init ops = c5
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 31 b4 a8 a0 0 c5 not ES chip
[2.756493 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-ge9754dd-dirty (Sep 08 2021 - 17:28:43)

DRAM:  1 GiB
Relocation Offset is: 36eef000
[MSG]MMC init in usb
aml_priv->desc_buf = 0x0000000033edf630
aml_priv->desc_buf = 0x0000000033ee1950
SDIO Port B: 0, SDIO Port C: 1
Enter USB burn
Set Addr 46
Get DT cfg
Get DT cfg
Get DT cfg
set CFG

ID[16]
tplcmd[ echo 12345]
12345
[MSG]ret = 0
[info]success
BULKcmd[ low_power]
[info]success

ID[16]
tplcmd[ download mem dtb normal 262144]
[MSG]Down(mem) part(dtb) sz(0x40000) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 4
[info]success
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x40000
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[disk_initial 0]
dtb magic 08088b1f
   Amlogic multi-dtb tool
   GZIP format, decompress...
   Multi dtb detected
   2layers board, board id use 7
   Multi dtb tool version: v2 .
   Support 10 dtbs.
      aml_dt soc: gxlx2 platform: p291 variant: 1g
      dtb 0 soc: gxl plat: p211 vari: 1g
      dtb 1 soc: gxl plat: p215 vari: 1g
      dtb 2 soc: gxlx plat: p261 vari: 1g
      dtb 3 soc: gxlx plat: p261 vari: 2g
      dtb 4 soc: gxlx plat: p265 vari: 1g
      dtb 5 soc: gxlx plat: p265 vari: 2g
      dtb 6 soc: gxlx2 plat: p291 vari: 1g
      dtb 7 soc: gxlx2 plat: p291 vari: 2g
      dtb 8 soc: gxlx2 plat: p295 vari: 1g
      dtb 9 soc: gxlx2 plat: p295 vari: 2g
   Find match dtb: 6
start dts,buffer=0000000007700000,dt_addr=0000000007700000
   Amlogic multi-dtb tool
   Single dtb detected
parts: 16
00:    logo 0000000002000000 1
01:  recovery 0000000002000000 1
02:    rsv 0000000000800000 1
03:    tee 0000000000800000 1
04:    crypt 0000000002000000 1
05:    misc 0000000002000000 1
06: instaboot 0000000020000000 1
07:    boot 0000000002000000 1
08: system 0000000040000000 1
09:    cache 0000000020000000 2
10: params 0000000004000000 2
11:    ctc 0000000012c00000 2
12: bootfiles 0000000020000000 2
13: private 0000000000800000 2
14: flashdata 0000000004000000 2
15:    data ffffffffffffffff 4
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd read error, cmd8, status=0xa3ff2004
emmc/sd read error, cmd8, status=0x3ff2004
[mmc_init] mmc init success
eMMC/TSD partition table have been checked OK!
check pattern success
switch to partitions #0, OK
mmc1(part 0) is current device
Device: SDIO Port C
Manufacturer ID: 15
OEM: 100
Name: 8GTF4
Tran Speed: 52000000
Rd Block Len: 512
MMC version 5.1
High Capacity: Yes
Capacity: 7.3 GiB
mmc clock: 40000000
Bus Width: 1-bit
start erase dtb......
start = 81920,end = 82943
dev # 1,  , several blocks erased OK
[store]To run cmd[emmc dtb_write 0x0000000001000000 0x40000]
dtb_write()-1147: valid 0
dtb_write()-1167: new stamp 0, checksum 0x2d38433b, version 1, magic A~D
dtb magic 08088b1f
   Amlogic multi-dtb tool
   GZIP format, decompress...
   Multi dtb detected
   2layers board, board id use 7
   Multi dtb tool version: v2 .
   Support 10 dtbs.
      aml_dt soc: gxlx2 platform: p291 variant: 1g
      dtb 0 soc: gxl plat: p211 vari: 1g
      dtb 1 soc: gxl plat: p215 vari: 1g
      dtb 2 soc: gxlx plat: p261 vari: 1g
      dtb 3 soc: gxlx plat: p261 vari: 2g
      dtb 4 soc: gxlx plat: p265 vari: 1g
      dtb 5 soc: gxlx plat: p265 vari: 2g
      dtb 6 soc: gxlx2 plat: p291 vari: 1g
      dtb 7 soc: gxlx2 plat: p291 vari: 2g
      dtb 8 soc: gxlx2 plat: p295 vari: 1g
      dtb 9 soc: gxlx2 plat: p295 vari: 2g
   Find match dtb: 6
start dts,buffer=0000000001000000,dt_addr=0000000001000000
dtb magic edfe0dd0
   Amlogic multi-dtb tool
   Single dtb detected
start dts,buffer=0000000001000000,dt_addr=0000000001000000
   Amlogic multi-dtb tool
   Single dtb detected
parts: 16
00:    logo 0000000002000000 1
01:  recovery 0000000002000000 1
02:    rsv 0000000000800000 1
03:    tee 0000000000800000 1
04:    crypt 0000000002000000 1
05:    misc 0000000002000000 1
06: instaboot 0000000020000000 1
07:    boot 0000000002000000 1
08: system 0000000040000000 1
09:    cache 0000000020000000 2
10: params 0000000004000000 2
11:    ctc 0000000012c00000 2
12: bootfiles 0000000020000000 2
13: private 0000000000800000 2
14: flashdata 0000000004000000 2
15:    data ffffffffffffffff 4
partition table success
[MSG]usb producing env_relocate
mmc env offset: 0x27400000
   Amlogic multi-dtb tool
   Single dtb detected
[info]success

ID[16]
tplcmd[download store boot normal 8216576]
[MSG]flash LOGIC partCap 0x2000000B
[MSG]Down(store) part(boot) sz(0x7d6000) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[info]success
[MSG]Burn Start...
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[verify sha1sum 15e0a2d94931ef0d05ff784eef046698a30504c8]
[MSG]Verify Start...
[MSG]To verify part boot in fmt normal
[MSG]Verify End
[MSG]VERIFY OK
[info]success

ID[16]
tplcmd[download store logo normal 33554432]
[MSG]flash LOGIC partCap 0x2000000B
[MSG]Down(store) part(logo) sz(0x2000000) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[info]success
[MSG]Burn Start...
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[verify sha1sum c4a22101f3c20744c7a463ca3b2dfb020b7c83a6]
[MSG]Verify Start...
[MSG]To verify part logo in fmt normal
[MSG]Verify End
[MSG]VERIFY OK
[info]success

ID[16]
tplcmd[download store recovery normal 13643776]
[MSG]flash LOGIC partCap 0x2000000B
[MSG]Down(store) part(recovery) sz(0xd03000) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1
[info]success
[MSG]Burn Start...
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[verify sha1sum e5095479e9d1282a90db95c2fe807125c334db2a]
[MSG]Verify Start...
[MSG]To verify part recovery in fmt normal
[MSG]Verify End
[MSG]VERIFY OK
[info]success

ID[16]
tplcmd[download store system sparse 554260696]
[MSG]flash LOGIC partCap 0x40000000B
[MSG]Down(store) part(system) sz(0x210958d8) fmt(sparse)
[MSG]totalSlotNum = 0, nextWriteBackSlot 1024
[info]success
[MSG]Burn Start...
[MSG]Burn complete
Downloading %100
BULKcmd[download get_status]
[info]success
BULKcmd[verify sha1sum 2bb96ff63c1a7253011b8bce88ed52276cbc85ce]
[MSG]Verify Start...
[MSG]To verify part system in fmt sparse
[MSG]Verify End
[MSG]VERIFY OK
[info]success

ID[16]
tplcmd[download store bootloader normal 2096640]
[MSG]Down(store) part(bootloader) sz(0x1ffe00) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 32
[info]success
[MSG]Burn Start...
mmc switch to boot0 success
mmc switch to boot1 success
mmc switch to user success
[MSG]align bootloader sz from 0x1ffe00 to 0x200000
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[verify sha1sum 2e5bfe05550137c321aeceb3727af177bd7adaf3]
mmc switch to boot0 success
mmc switch to boot1 success
mmc switch to user success
[MSG]VERIFY OK
[info]success
BULKcmd[save_setting]
## save_setting ##
[MSG]Set upgrade_step to 2
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
[info]success
BULKcmd[burn_complete 3]
[MSG]Pls un-plug USB line to poweroff
[info]success

但是重啟后無法啟動系統，ttl跑碼顯示如下，：
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:1;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:2;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:3;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:4;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:5;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8...（一直循環，LOOP值增加）
制作TF啟動卡，仍無法啟動系統，ttl跑碼顯示如下：
BL2 Built : 17:04:12, Jun 21 2016.
gxl g21e86b3 - yao.zhang@droid07
set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 8
CPU clk: 1200MHz
DDR chl: Rank0+1 @ 792MHz - FAIL
DDR chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:4;READ:4;READ:4;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 163960

有沒有遇到相同問題的玩家，另外正常的線刷包一般2、3分鐘就能刷完，而現在同樣大小的線刷包至少耗時5分多鐘，不知道什么原因造成的。

月下橋 · 發表于 2023-3-18 15:50

這類盒子被不斷的精進，有一些刷機固件出來，這些刷機固件能解決的問題非常多，例如電視盒子卡頓、機頂盒死機，甚至是機頂盒變磚黑屏，都可能會被就活。所以的人通過刷機延長使用壽命，但是配置方面一直是硬傷，早已經和時代脫軌，安裝了幾款軟件就會出現死機現象，已經不再是刷機能夠解決的了。

眾多電視盒子新品中，我最想推薦的就是當貝MAX 1電視盒子，當貝MAX 1是首款采用6G運存的電視盒子，搭配64G的超大內存，配備瑞芯微RK3566芯片，其性能完全秒殺晶晨S905系列和全志芯片，讓體驗變得更加的流暢，享受到的功能也是越來越多。

其次就是當貝OS系統，它沒有軟件的安裝限制，可隨意安裝多款應用，并且UI交互設計流暢，并且具備人性化設計，支持自定義桌面編輯，讓用戶使用的更加舒心。

這樣的一款產品才是目前市場上主流的電視盒子應該具備的素質，如果說價格和你的預期不等，你也完全可以看看當貝盒子H2，雖然只有2+16G的內存，但是擁有晶晨S912八核處理器的芯片，其性能也是這類盒子無法比的。

guguai · 發表于 2023-11-19 14:49

沒有DTB文件分享碼？

› 智能電視盒 / 安卓TV機頂盒區 › 其它品牌盒子

數碼視訊Q7刷機問題

數碼視訊Q7刷機問題

相關帖子